GM Service Manual Online
For 1990-2009 cars
Makes 🢒 Holden 🢒 2009 🢒 Viva 🢒 Preface 🢒 Dangers, Warnings, and Cautions 🢒 Steering Wheel Replacement

Steering Wheel Replacement With SIR

Special Tools
    • J 1859-A Steering Wheel Puller
    • J 36541-A Puller Legs
    • KM-210-A Steering Wheel Puller

Removal Procedure

    Warning: Refer to Battery Disconnect Warning in the Preface section.


    Object Number: 1308218 Size: SH
  1. Disconnect the negative battery cable.
  2. Remove the SIR module. Refer to Inflatable Restraint Steering Wheel Module Replacement.
  3. Remove the steering wheel nut and the retaining clip.
  4. Use paint in order to place match marks on the steering wheel and on the steering shaft.

    5. Object Number: 1308216 Size: SH
  5. Remove the steering wheel using the KM-210-A or the J 1859-A and the J 36541-A  (1).
  6. Unclip the contact ring from the steering wheel, if necessary.

Installation Procedure

    Object Number: 1308220 Size: SH
  1. Clip the contact ring on the steering wheel, if necessary.
  2. Align the match-marks on the steering wheel and the steering column shaft. Turn the signal cancelling cam on the wheel to the left.

    3. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the retaining clip and the steering wheel nut and tighten to 38 N·m (28 lb ft).
  4. Bend the tabs to secure the retaining clip.
  5. Install the SIR module. Refer to Inflatable Restraint Steering Wheel Module Replacement.
  6. Connect the negative battery cable.

Steering Wheel Replacement Without SIR

Special Tools
    • J 1859-A Steering Wheel Puller
    • J 36541-A Puller Legs
    •  KM-210-A Steering Wheel Puller

Removal Procedure

    Warning: Refer to Battery Disconnect Warning in the Preface section.


    Object Number: 1308134 Size: SH
  1. Disconnect the negative battery cable.
  2. Rotate the steering wheel to allow access to the steering wheel horn cap screw. Remove the horn cap screw.
  3. Rotate the steering wheel to allow access to the other steering wheel horn cap screw. Remove the horn cap screw.

    4. Object Number: 1308164 Size: SH
  4. Remove the steering wheel horn cap and disconnect the horn leads.

    5. Object Number: 1308166 Size: SH
  5. Remove the steering wheel nut and the retaining clip.

    6. Object Number: 1308216 Size: SH

    Note: In order to install the steering wheel correctly, match-mark the steering column shaft to the steering wheel.

  6. Remove the steering wheel using the KM-210-A or the J 1859-A and the J 36541-A  (1).
  7. Unclip the contact ring from the steering wheel, if necessary.

Installation Procedure

    Object Number: 1308166 Size: SH
  1. Clip the contact ring on the steering wheel, if necessary.
  2. Align the match-marks on the steering wheel and the steering column shaft.

    3. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the retaining clip and the new steering wheel nut and tighten to 38 N·m (28 lb ft).

    4. Object Number: 1308164 Size: SH
  4. Bend the tabs to secure the retaining clip.
  5. Connect the horn leads and install the steering wheel horn cap.

    6. Object Number: 1308134 Size: SH
  6. Rotate the steering wheel to allow access to the steering wheel horn cap screw. Install the horn cap screw.
  7. Rotate the steering wheel to allow access to the other steering wheel horn cap screw. Install the horn cap screws and tighten to 4.5 N·m (40 lb in).
  8. Connect the negative battery cable.